Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 13

Page: 13 / 92

Getting Help

HSIM-W6 Installation Guide

1-3

Getting Help

If you need additional support related to this device, or if you have any questions, comments, or
suggestions concerning this manual, contact the Cabletron Systems Global Call Center:

Before calling the Cabletron Systems Global Call Center, have the following information ready:

•

Your Cabletron Systems service contract number

•

A description of the failure

•

A description of any action(s) already taken to resolve the problem (e.g., changing mode
switches, rebooting the unit, etc.)

•

A description of your network environment (layout, cable type, etc.)

•

Network load and frame size at the time of trouble (if known)

•

The serial and revision numbers of all involved Cabletron Systems products in the network

•

The device history (i.e., have you returned the device before, is this a recurring problem, etc.)

•

Any previous Return Material Authorization (RMA) numbers

Phone

(603) 332-9400

Internet mail

[email protected]

FTP

ctron.com (134.141.197.25)

anonymous

Password

your email address

BBS

(603) 335-3358

Modem setting

8N1: 8 data bits, No parity, 1 stop bit

For additional information about Cabletron Systems or our products,
visit our World Wide Web site:

http://www.cabletron.com/

For technical support, select

Service and Support

Summary of Contents for CyberSWITCH HSIM-W6





























































































Search results

Summary of Contents for CyberSWITCH HSIM-W6

Reviews:

Related manuals for CyberSWITCH HSIM-W6

Brands by name

Popular brands

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Search results

Summary of Contents for CyberSWITCH HSIM-W6

Reviews:

Related manuals for CyberSWITCH HSIM-W6

Brands by name

Popular brands