manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 17

Remote Management Capabilities

HSIM-W6 Installation Guide

2-3

•

The WPIM-T1/DDS provides both a T1 and DDS interface that allows changing between the 
two interfaces by switching the physical cabling and reconfiguring QuickSET for the desired 
interface. The WPIM-T1/DDS has the capabilities of both the WPIM-T1 and WPIM-DDS.

Additional Features

FLASH EEPROMs —

The HSIM-W6 uses FLASH Electrically Erasable Programmable 

Read-Only Memory (EEPROM) that allows the downloading of new and updated firmware in 
conjunction with Cabletron Systems QuickSET or any device using BootP or TFTP protocols.

LANVIEW LEDs —

Cabletron Systems LANVIEW Status Monitoring and Diagnostics System is 

a troubleshooting tool that helps in the diagnosing of power failures, collisions, cable faults, and 
link problems. The LANVIEW LEDs are located on the HSIM-W6 front panel.

Remote Management Capabilities

The HSIM-W6 can be remotely managed with any SNMP network management system including 
the following:

•

Cabletron Systems SPECTRUM for Open Systems Suite of Network Management Products

•

Cabletron Systems QuickSET

•

Third Party SNMP compliant Network Management Packages

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands