manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 34

Chapter 2: About the HSIM-W6

2-20

HSIM-W6 Installation Guide

The following is a list of IP Events that are logged and that create the IP Event Log Change Trap.

•

IP Routing has been disabled on interface #

•

IP Routing has been enabled on interface #

•

IP Forwarding has been enabled on interface #

•

IP MTU size has been changed on interface #

•

IP Framing Type has been changed on interface #

•

IP has detected Link UP on interface #

•

IP has detected Link DOWN on interface #

•

IP Primary address has been changed on interface #

•

IP Secondary address has been changed on interface #

•

IP Access Control Lists have been enabled on interface #

•

IP Access Control Lists have been disabled on interface #

•

IP has detected Port UP (WAN devices only)

•

IP has detected Port DOWN (WAN devices only)

•

IP Proxy ARP has been disabled on interface #

•

IP Proxy ARP has been enabled on interface #

•

IP RIP has been enabled on interface #

•

IP RIP has been disabled on interface #

•

IPX Event Log Change Trap Type Code #1281(0x501) ctipx-mib

•

The following is a list of IPX Events that are logged and that create the IPX Event Log Change 
Trap.

•

IPX Routing has been disabled on interface #

•

IPX Routing has been enabled on interface #

•

IPX Forwarding has been enabled on interface #

•

IPX MTU size has been changed on interface #

•

IPX Framing Type has been changed on interface #

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands