manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 76

Appendix B: Specifications and Standards Compliance

B-2

HSIM-W6 Installation Guide

Individual WPIM Regulatory Compliance

The following sections provide regulatory compliance standards for the WPIM-TI, WPIM-SY, 
WPIM-DDS, WPIM-E1, WPIM-DI, WPIM-S/T, and the WPIM-HDSL. Cabletron Systems 
reserves the right to change these specifications at any time without notice.

WPIM-TI

This section describes the environmental specifications and safety and approval requirements for 
the WPIM-T1.

Safety —

This unit meets the safety requirements of UL 1950, and CSA C22.2 No. 950.

Electromagnetic Compatibility (EMC) —

This unit meets the EMC requirements of FCC Part 

15, VCCI V-3, and CSA C108.8.

NEBS —

This unit meets a minimum of Level 1 NEBS requirements in accordance with Bellcore 

SR 3580.

TELECOM —

FCC Part 68, CS-03.

WPIM-SY

This section describes the environmental specifications and safety and approval requirements for 
the WPIM-SY. 

Safety —

This unit meets the safety requirements of UL1950, CSA C22.2 No. 950, EN 60950, 

IEC 950, and 73/23/EEC.

EMI —

This unit meets the EMI requirements of FCC Part 15, EN 55022, EN 50082-1, AS/NZS 

3548, 89/336/EEC, CSA C108.8, and VCCI V-3.

TELECOM —

91/263/EEC, and NET 2.

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands