manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 9

 

Contents

 

HSIM-W6 Installation Guide

vii

 

Status (STS) LED is RED ...........................................................................4-9

Status (STS) LED is AMBER .....................................................................4-9

Status (STS) LED is AMBER (blinking) ..................................................4-10

Status (STS) LED is GREEN....................................................................4-10

Investigating Software Configuration Problems .........................................4-11

Connection to Device Fails During Software Configuration................4-11

User Cannot Communicate with Remote Network Station ..................4-11

Troubleshooting the Frame Relay Connection .....................................4-12

APPENDIX A

WPIM CABLE SPECIFICATIONS

WPIM-T1 ........................................................................................................... A-1

WPIM-SY ........................................................................................................... A-3

EIA-449 ....................................................................................................... A-4

V.35............................................................................................................. A-5

EIA-232 ....................................................................................................... A-7

X.21............................................................................................................. A-8

EIA-530, EIA-530 ALT A, EIA-530 A, and EIA-530 A ALT A.................... A-9

WPIM-DDS ...................................................................................................... A-11

WPIM-E1 ......................................................................................................... A-12

WPIM-DI .......................................................................................................... A-14

WPIM-HDSL .................................................................................................... A-15

WPIM-S/T ........................................................................................................ A-16

APPENDIX B

SPECIFICATIONS AND STANDARDS COMPLIANCE

Regulatory Compliance .................................................................................. B-1

Individual WPIM Regulatory Compliance ...................................................... B-2

WPIM-TI ...................................................................................................... B-2

WPIM-SY .................................................................................................... B-2

WPIM-DDS.................................................................................................. B-3

WPIM-E1..................................................................................................... B-3

WPIM-DI...................................................................................................... B-3

WPIM-S/T.................................................................................................... B-4

WPIM-HDSL ............................................................................................... B-4

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands