manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 8

 

Contents

 

vi

HSIM-W6 Installation Guide

 

System Passwords ..................................................................................2-17

Simple Network Management Protocol (SNMP)....................................2-18

Software and Firmware Upgrades ..........................................................2-21

CHAPTER 3

INSTALLATION

Unpacking the HSIM-W6 ..................................................................................3-1

Guidelines for Installations .............................................................................3-1

Installing Interface Modules ............................................................................3-2

Installing WAN Port Interface Modules (WPIMs) ...........................................3-2

CSX-COMP/ENCR Installation .........................................................................3-4

Installing an HSIM.............................................................................................3-6

Installing an HSIM in an Interface Module ...............................................3-6

Installing an HSIM in a SmartSWITCH Chassis.......................................3-9

CHAPTER 4

TROUBLESHOOTING

Troubleshooting HSIM-W6 Hardware .............................................................4-5

Power (PWR) LED is OFF ..........................................................................4-5

Processor (CPU) LED is OFF ....................................................................4-5

Processor (CPU) LED is RED....................................................................4-6

ASYNC Console Connection ...........................................................................4-6

Link (LNK) LED is OFF...............................................................................4-6

Link (LNK) LED is RED or GREEN............................................................4-6

Link (LNK) LED is AMBER.........................................................................4-6

Status (STS) LED is OFF ...........................................................................4-6

Status (STS) LED is AMBER .....................................................................4-6

Status (STS) LED is GREEN or GREEN (Blinking)..................................4-6

Status (STS) LED is AMBER (Blinking)....................................................4-7

Troubleshooting the WAN ...............................................................................4-7

Link (LNK) LED is OFF...............................................................................4-7

Link (LNK) LED is RED ..............................................................................4-7

Link (LNK) LED is AMBER.........................................................................4-7

Status (STS) LED is OFF ...........................................................................4-8

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands