manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 35

HSIM-W6 Firmware Support

HSIM-W6 Installation Guide

2-21

•

IPX has detected Link UP on interface #

•

IPX has detected Link DOWN on interface #

•

IPX Primary address has been changed on interface #

•

IPX Access Control Lists have been enabled on interface #

•

IPX Access Control Lists have been disabled on interface #

•

IPX has detected Port UP (WAN devices only)

•

IPX has detected Port DOWN (WAN devices only)

•

IPX RIP has been enabled on interface #

•

IPX RIP has been disabled on interface #

•

IPX SAP has been enabled on interface #

•

IPX SAP has been disabled on interface #

Software and Firmware Upgrades

Software and Firmware upgrades can be performed remotely through the Windows-based 
QuickSET utility application. Refer to the QuickSET Configuration Guide for instructions. 
QuickSET allows the user to retrieve or upgrade the firmware, software, and configuration files 
from its Firmware Upgrade menu by selecting the TFTP/BootP Services window to access a 
TFTP (Trivial File Transfer Protocol) server.

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands