Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 39

Page: 39 / 92

Installing WAN Port Interface Modules (WPIMs)

HSIM-W6 Installation Guide

3-3

Figure 3-1 Removing the WPIM Coverplate

Remove and save the two HSIM faceplate screws attaching the faceplate to the HSIM printed
circuit board (PCB). Remove the HSIM faceplate (see Figure 3).

Carefully align and gently insert the WPIM connector onto the WPIM connector pins on the
HSIM-W6.

Press down firmly on the WPIM until the pins slide all the way into the connector. Ensure that
the WPIM seats firmly on the standoffs.

Secure the WPIM to the three standoffs using the screws that are provided with the HSIM-W6.

Reattach the faceplate to the HSIM using the two screws saved in step 3.

WPIM

Coverplate

Standoff Screws

HSIM Standoffs

Summary of Contents for CyberSWITCH HSIM-W6





























































































Search results

Summary of Contents for CyberSWITCH HSIM-W6

Reviews:

Related manuals for CyberSWITCH HSIM-W6

Brands by name

Popular brands

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Search results

Summary of Contents for CyberSWITCH HSIM-W6

Reviews:

Related manuals for CyberSWITCH HSIM-W6

Brands by name

Popular brands