manualshive.com logo in svg

Cabletron Systems CyberSWITCH HSIM-W6, Installation Manual

Share
Download
Cabletron Systems CyberSWITCH HSIM-W6 Installation Manual Download Page 7

 

HSIM-W6 Installation Guide

v

 

Contents

 

CHAPTER 1

INTRODUCTION

Structure of this Guide.....................................................................................1-1

Related Documents ..........................................................................................1-2

Document Conventions ...................................................................................1-2

Getting Help ......................................................................................................1-3

CHAPTER 2

ABOUT THE HSIM-W6

HSIM-W6 Hardware...........................................................................................2-1

WAN Connection........................................................................................2-1

Additional Features ...................................................................................2-3

Remote Management Capabilities ..................................................................2-3

Optional Feature ...............................................................................................2-4

HSIM-W6 Firmware Support ............................................................................2-4

WAN Protocols ...........................................................................................2-4

Inverse Multiplexing ..................................................................................2-6

Firmware Data Compression ....................................................................2-6

HDLC ...........................................................................................................2-7

DHCP and NAT ...........................................................................................2-7

Frame Relay Protocol ................................................................................2-8

Point-to-Point Protocol..............................................................................2-9

PAP and CHAP Security ............................................................................2-9

LQM ...........................................................................................................2-10

Multilink Protocol .....................................................................................2-10

ISDN ..........................................................................................................2-11

ISDN Back-up ...........................................................................................2-12

The IP-OSPF Routing Protocol ...............................................................2-12

IP-OSPF Hierarchy ...................................................................................2-13

HDSL .........................................................................................................2-15

Bridging and Routing ..............................................................................2-15

Bridging and Routing Protocol Filtering................................................2-17

Summary of Contents for CyberSWITCH HSIM-W6





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands