BYD BYD5030XXYBEV2 Manual Download Page 236 | Manualshive

Page: 236 / 252

background image

236

8-1 When Failure Occurs



If the tyre pressure is in the range of
180~320kPa (yellow and green zones
shown in the figure), remove the kit as
soon as possible, and within 1 min, start
driving the vehicle at a speed lower than
80km/h for a distance not exceeding 10
km to allow the tyre puncture sealant to
be uniformly distributed in the tyre.

8. Stop the vehicle and observe the tyre
pressure.



If the tyre pressure is greater than
220kPa (green zone shown in the
figure), drive the vehicle at a speed
lower than 80km/h to a nearest service
provider.



If the tyre pressure is in the range of
130~220kPa (yellow zone shown in the
figure), repeat steps 6 and 7.



If the tyre pressure does not reach 130
kPa (red zone shown in the figure),
contact a BYD authorised service
provider.

WARM TIP



Repairing a damaged tyre with tyre puncture sealant is an emergency solution only.
Please replace the tyre in a professional maintenance center as soon as possible (it is
recommended that you contact a BYD authorised service provider) and tell a
professional technician that the tyre has tyre puncture sealant inside.



Avoid quick acceleration or turning at a high speed.



Follow the limit requirement of maximum vehicle speed of 80km/h.



After repairing a tyre with the tyre puncture sealant kit, it is recommended that you
purchase a new tyre puncture sealant and inflator hose from a BYD authorised service
provider.

«
...
234
235
236
237
238
...
»

Summary of Contents for BYD5030XXYBEV2





























































































































































































































































Reviews:

No comments

Related manuals for BYD5030XXYBEV2

Brand: Federal Signal Corporation Pages: 13

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: NavLinkz Pages: 4

Brand: Metra Electronics Pages: 2

Brand: Kia Pages: 10

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: Saab Pages: 3

Brand: Safe Fleet Pages: 11

Brand: Camec Pages: 19

Brand: EUFAB Pages: 52

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: iSimple Pages: 12

Brand: RAWLINK Pages: 25

Brand: Genesis Pages: 690

FUEL TANK GAUGE

Brand: VDO Pages: 10

Brand: Toyota Pages: 277

Brand: TOP VEHICLE TECH Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands