BYD BYD5030XXYBEV2 Manual Download Page 45

Page: 45 / 252

stru

t Set

2-1 Combination Instrument Appearance



Travelling time

It indicates the travelling time in OK
mode from the previous resetting.
Pressing and holding the steering wheel
button

for more than 2s can

reset the information to zero.



Energy flow

This information indicates the state of
energy flow among the motor, battery
and wheel.



Tyre pressure display interface

It indicates the pressure and
temperature values of each tyre.

Prompt information



On the charging interface, the current
charging information is displayed.

On the interface, press the steering
wheel button

to enter the

preset charging setting interface
(during AC charging).

Summary of Contents for BYD5030XXYBEV2





























































































































































































































































Search results

Summary of Contents for BYD5030XXYBEV2

Reviews:

Related manuals for BYD5030XXYBEV2

Brands by name

Popular brands

BYD BYD5030XXYBEV2, Manual

Search results

Summary of Contents for BYD5030XXYBEV2

Reviews:

Related manuals for BYD5030XXYBEV2

Brands by name

Popular brands