BYD BYD5030XXYBEV2 Manual Download Page 178 | Manualshive

Page: 178 / 252

background image

178

6-3 Other Devices

6-3 Ot her Devic es

Power Socket

The power socket is used for providing
power for vehicle accessories. When using
the power socket, open its cover and vehicle
power must be in OK mode.

Sun Visor



The sun visors are located above the
driver's seat/front passenger's seat (if
any).



To shade the eyes from glare of sunlight
from the front, pull down the sun visor.

«
...
176
177
178
179
180
...
»

Summary of Contents for BYD5030XXYBEV2





























































































































































































































































Reviews:

No comments

Related manuals for BYD5030XXYBEV2

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

Brand: iDataLink Pages: 30

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Ford Pages: 12

Brand: Phonocar Pages: 2

Brand: FAAFTECH Pages: 8

Brand: AutoMaxi Pages: 2

Vantage 12 Series

Brand: Ecco Pages: 5

Brand: Porsche Pages: 313

Brand: Mazda Pages: 122

Brand: Easee Pages: 12

Brand: Chevrolet Pages: 428

Brand: Cadillac Pages: 409

Brand: Fortin Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands