![background image](http://html1.mh-extra.com/html/bush-hog/12814/12814_operators-manual_2834782119.webp)
OPERATION
2814-2820
08/20 Operation Section 4-15
© 2020 Alamo Group Inc.
OPERA
TION
NOTE:
If tractor has a 540 RPM PTO, adjusting to a 16 inch position will gain additional 2 inches of telescoping
length.
“Bottoming Out” Check Procedure
•
Disconnect driveline from the tractor and slide
the profiles together until fully compressed.
•
Place a mark on the inner shield 1/8” from the
end of the outer shield and reattach the
driveline to the PTO shaft.
•
With the
PTO NOT TURNING
, slowly drive the
tractor with mower attached through the
sharpest turn possible and watch shaft
movement. With the
PTO NOT TURNING
,
slowly drive the tractor with the mower attached
through the most severe terrain conditions
expected and watch shaft movement.
•
If the distance between the mark and the outer
shield becomes less than 2” at any point there is a potential problem bottoming out the driveline and the
driveline should be replaced with shorter driveline. Contact your local dealer or Technical Service for
proper directions.
OPS-R-0004_J
Engagement Check Procedure
•
With the driveline attached, position the mower to the point where the telescoping driveline is at its maximum
extension. Completely shut down the tractor and secure in position.
•
Mark the inner driveline shield 1/8” from the end of the outer shield.
•
Disconnect the driveline from the tractor and separate the two driveline halves.
•
Measure the distance from the mark to the end of the inner profile. This length is the amount the driveline profiles were
engaged.
•
If the engaged length is less than 6”, the shaft is considered too short and should be replaced with a longer shaft.
Consult an authorized dealer to purchase the required driveline length.
NOTE:
If the driveline cannot be shortened and still maintain the required profile engagement, the operator must be made
aware of terrain conditions and avoid situations which pose a potential problem to avoid damaging the driveline or move
drawbar to 16” or 20” position for required clearance. OPS-R-0005_O
Summary of Contents for 12814
