
OPERATION
2814-2820
08/20 Operation Section 4-42
© 2020 Alamo Group Inc.
OPERA
TION
13. MOWER STORAGE
It is recommended that the mower be stored with the center section and both wings fully lowered to ground
level. If the mower is stored with the wings in the raised position, select a level area and install wing transport
lock pins to prevent the wings from falling BEFORE disconnecting the mower hitch from the tractor.
Properly preparing and storing the mower at the end of the season is critical to maintaining its appearance
and to help ensure years of dependable service. The following are suggested storage procedures:
•
Thoroughly clean all debris off the mower to
prevent
damage
from
rotting
grass
and
standing water.
•
Lubricate all mower grease points and fill
gearbox
oil
levels
as
detailed
in
the
maintenance section.
•
Tighten all bolts and pins to the recommended
torque.
•
Check the mower for worn and damaged
parts.
Perform
repairs
and
make
replacements immediately so that the mower
will be ready for use at the start of the next
season.
•
Store the mower in a clean, dry place with the
mower housing resting securely on blocks or
at ground level.
•
Keep the driveline yoke from sitting in water,
dirt and other contaminants.
•
Use spray touch-up enamel where necessary
to prevent rust and maintain the appearance of
the mower.
It is critical that driveline clutches slip when an obstacle or heavy load is encountered to avoid mower and/or
tractor damage. If the mower sits outside for an extended period of time or is exposed to rain and/or humid
air, the clutch lining plates must be inspected to ensure they are not frozen together from rust or corrosion. If
the mower has been exposed to such conditions, at the start of each mowing season, and any time it is
suspected that the slip clutch plates may be frozen together, readjust the slip clutch as detailed in Seasonal
Clutch Maintenance of the maintenance section in this manual.
OPS-R-0032_H
Never allow children to play on or around Tractor or Implement. Children can slip or fall off
the Equipment and be injured or killed. Inadvertent contact with controls can cause the
Implement to shift or fall crushing themselves or others.
(SG-25)
14. TRANSPORTING THE TRACTOR AND IMPLEMENT
Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind
when you finish working in an area. Therefore, the operator must employ good judgement and safe operation
practices when transporting the tractor and implement between locations. By using good judgement and
following safe transport procedures, the possibility of accidents while moving between locations can be
substantially minimized.
OPS-U- 0017
Summary of Contents for 12814
