![background image](http://html1.mh-extra.com/html/bush-hog/12814/12814_operators-manual_2834782109.webp)
OPERATION
2814-2820
08/20 Operation Section 4-5
© 2020 Alamo Group Inc.
OPERA
TION
3. Tractor Horsepower
The horsepower required to operate the mower depends on several operating factors including the vegetation
to be cut, terrain condition, operator experience, condition of the mower and tractor, and others. For most
mowing conditions, the 2814/12814 and 2820/12820 mower requires a tractor with a minimum of 90 HP.
Operating the mower with a tractor that does not have adequate power may damage the tractor engine.
Exceeding 120 HP may cause mower damage by overpowering the unit in heavy cutting conditions.
3.1 Drawbar
Constant Velocity and Standard Driveline
.
Position the length of the drawbar from the end of
the tractor PTO shaft to the drawbar hitch hole
according to the operating speed of the mower. If
the mower is a 540 RPM unit, position the drawbar
length from shaft end to hitch hole at 14”. For 1000
RPM mowers, set the drawbar length at 16” for 21
spline 1-3/8” mowers and at 20” for 1-3/4” 20 spline
mowers. Do not use PTO adaptors. Use of PTO
adaptors will invalidate your warranty.
3.2 Tractor Hydraulics
The mower center section and each wing are positioned with hydraulic cylinders that are operated by the
tractor hydraulic pump. The tractor must have a minimum of 2 hydraulic control valves devoted to the mower
unless the tractor is fitted with a 3-spool control valve (extra equipment).
A 3-spool control valve is required if the tractor is equipped with a single valve and is recommended for those
with two valves so that the center section and each wing can be controlled independent of one another. Refer
to the Assembly Section of this manual for properly equipping the tractor with a 3-spool control valve. Tractors
equipped with three hydraulic ports can position the center section and each wing independently with no extra
equipment. If the tractor is equipped with only two hydraulic ports and a 3-spool control valve is not used, the
wings cannot be operated independently and will raise and lower at different speeds.
3.3 Front End Weight
A minimum of 20% total tractor weight must be maintained on the tractor front end at all times. Front end
weight is critical to maintain steering control and to prevent the tractor from rearing up while driving. If the
front end is too light, add weight until a minimum of 20% total weight is reached on the front tires. Front
weights and weight carriers can be purchased through an authorized tractor dealership.
OPS-U- 0005
Summary of Contents for 12814
