![background image](http://html1.mh-extra.com/html/bush-hog/12814/12814_operators-manual_2834782171.webp)
MAINTENANCE
2814-2820 08/20
Maintenance Section 5-17
© 2020 Alamo Group Inc.
SKID SHOES
Skid shoes are made of carbon steel to reduce wear and increase service life. Premature wear can be caused
by the mower Center or Wing sections being set too low which allows the Wing Skid Shoes to drag on the
ground. Dragging the Skid Shoes on the ground or running the Skid Shoes into solid objects can contribute to
early frame failure on the mower. Replace worn Skid Shoes as required.
STORAGE
Your rotary cutter represents an investment from which you should get the greatest possible benefit. Therefore,
when the season is over, the cutter should be thoroughly checked and prepared for storage so that a minimum
amount of work will be required to put it back into operation for the next season. The following are suggested
storage procedures:
1.
Thoroughly clean the cutter.
2.
Lubricate the cutter as covered in Maintenance Section.
3.
Tighten all bolts and pins to the recommended torque.
4.
Check the cutter for worn or damaged parts. Make replacements immediately.
5.
Store the cutter in a clean, dry place with the cutter housing resting on blocks.
6.
Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the cutter.
PROPER TORQUE FOR FASTENERS
The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to
this chart to determine the grade of bolts and the proper torque except when specific torque values are
assigned in manual text.
RECOMMENDED TORQUE IN FOOT POUNDS UNLESS OTHERWISE STATED IN THE MANUAL*
NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal engine
oil. They do not apply if special graphited or molydisulphide greases or other extreme pressure lubricants are
used. This applies to both UNF fine and UNC coarse threads.
MAINTENANCE
Summary of Contents for 12814
