manualshive.com logo in svg

Burster RESISTOMAT 2408, Manual, Page: 87 / 90

Share
Download
Burster RESISTOMAT 2408 Manual Download Page 87

Model  2408

RESISTOMAT

®

Page 87

5.1.3 

Loss of Display Contrast

If for some reason the instrument should loose its display contrast it is possible to reset it 
easily using the procedure below. 

Loss of contrast would exhibit no display at all when 

the instrument is powered up.  

Procedure for restoring loss of contrast:

1.  Consider the SELECT buttons as labeled 1, 2, 3, and 4 from top to bottom.

2.  Turn the instrument on and wait 20 seconds (or after High Voltage light flashes)

3.  Press [MENU] key twice.

4.  Press [SELECT “4”] one time.
5.  Press [SELECT “1”] two times.

6.  Press [ENTER].

7.  Press [SELECT “1”] many times till contrast returns to normal.

8.  Press [ENTER].
9.  Arrow up to [SAVE SETUP] and save as [DEFAULT].

If the above procedure fails to restore the contrast try repeating again. Failing restoration of 
the contrast may be indication of another instrument problem.

5.1.4 

Preventive Maintenance

In addition to the annual battery replacement and calibration discussed below periodic 
cleaning of dust is recommended depending on the environmental conditions.

Summary of Contents for RESISTOMAT 2408



























































































Reviews:

No comments