manualshive.com logo in svg

Burster RESISTOMAT 2408, Manual, Page: 21 / 90

Share
Download
Burster RESISTOMAT 2408 Manual Download Page 21

Model  2408

RESISTOMAT

®

Page 21

Setting Pass/Fail Limit

1.  To enter a single measurement limit for resistance or current (depending on results    
 

display selected):

 

  Press [MENU] key to  select menu display.

 

  Press Right or Left Arrow to select  Setup menu.

 

  Press Up or Down Arrow key to select Limit in sub menu.

 

  Press [ENTER] key to activate the limit entry field.

 

  Enter the numerical value

 

(up to 4 digits plus decimal point) of the limit desired,    

 

  then enter the exponential value

 

after first pressing the 

e

 select key (use minus    

 

  exponential value for current).

 

  Press [ENTER] key to finalize the limit entry.

Changing Display Type and Units

1.  To change displayed measurement results between Resistance, Current or Pass/Fail:

 

  Press [MENU]

 

key to select menu display.

 

  Press Right or Left Arrow key to select I/O Menu.

 

  Press Up or Down Arrow key to select Display.

 

  Press [ENTER] key to activate the selection field.

 

  Press Up or Down Arrow key to select desired measurement results,  

 

 

 

  Resistance, Current or Pass/Fail if a limit is to be used.

 

  Press [ENTER] key to finalize the entry.

2.  To change the measurement results format between Scientific or Engineering units:

 

  Press [MENU] key to select menu display.

 

  Press Right or Left Arrow key to select I/O Menu.

 

  Press Up or Down Arrow key to select Result Format.

 

  Press

 

[ENTER] key to activate the selection field.

 

  Press Right or Left Arrow to select desired results format, Sci for Scientific or    

 

  Eng for Engineering.

 

  Press [ENTER]

 

key to finalize the entry.

Summary of Contents for RESISTOMAT 2408



























































































Reviews:

No comments