Burster RESISTOMAT 2408 Manual Download Page 74

Page: 74 / 90

RESISTOMAT

Model 2408

Page 74

„PASSWORD NOT SAVED IN RAM“

Error trying to save password, repeat

„PASSWORD VERIFICATION FAILURE“

Wrong password entry for verification

„RANGE RESISTOR VALUE OUT OF RANGE“ Malfunction of internal calibration resistors

„REMOTE COMMAND INVALID“

IEEE or RS232 command is incorrect (for

example: to set voltage use VOLTage)

„REMOTE COMMAND PARAMETER

IEEE or RS232 parameter is incorrect (for

INVALID“

example: voltage parameter can be

XXXX.XXX)

„REMOTE COMMAND PREFIX INVALID“

IEEE or RS232 command prefix is

incorrect (for example: to configure unit

use CONFigure)

„SHUT THE POWER OFF“

Malfunction of high voltage source

„TIME / DATE ERROR, PLEASE SET“

Reset time and date

“UNABLE TO READ FROM USB”

Flash drive is either not connected or

defective

“UNABLE TO READ THAT FILENAME”

Selected file unreadable, improper format

“UNABLE TO SAVE CALIBRATION DATA”

Repeat calibration, data not stored

“UNABLE TO WRITE TO USB”

Flash drive is either not connected or

defective

“UNABLE TO WRITE TO REMOTE”

IEEE or RS232 not setup correctly or IEEE

option not present

“UNKNOWN UNIT”

USB is not recognized

“VALID RANGE = low value - hi value”

Entry invalid, should be between specified

values

“VOLTAGE PROGRAM FAILURE”

Malfunction of instrument power supplies

Summary of Contents for RESISTOMAT 2408



























































































Search results

Summary of Contents for RESISTOMAT 2408

Reviews:

Burster RESISTOMAT 2408, Manual, Page: 74 / 90

Search results

Summary of Contents for RESISTOMAT 2408

Reviews: