Home
/
Burster
/
RESISTOMAT 2408
/
Manual

Burster RESISTOMAT 2408, Manual, Page: 46 / 90

Share

Page: 46 / 90

Burster RESISTOMAT 2408 Manual Download Page 46

RESISTOMAT

®

Model 2408

Page 46

2.6.2.9 Stop on Pass

Accepts entry of a value between 0 and 300 which is the number of consecutive pass-
ing measurements that must occur to exit the measure loop before the measure time has

passed. This is only active when there is a measure time and limit specified. An entry of 0

disables the stop on pass function.

2.6.2.10 # to Average

Accepts entry of a value between 0 and 400 which is the number of measurements to
be averaged and displayed. If the value is 0 or 1 averaging is disabled and the display is
updated with each measurement, if the value is n (between 2 and 400) the average is dis-

played after n measurements. If the measure time has not elapsed after the first averaged

display, then a running average of measurements is made until the measure time is up. For

example, if n is 5, the first five measurements are made, averaged and then displayed. The
sixth measurement is averaged with the last four and the first ignored, this continues until
the user specified measurement time is complete.

When Stop on Pass is in effect, n measurements are made and averaged.

If the Stop on Pass requirement is met, the cycle stops with a Pass even though the
measure time has not passed.

If the measure time has passed and the Stop on Pass requirement has not been met,
the cycle stops with a Fail.

If the Stop on Pass requirement is not met, and the measure time has not passed,
additional measurements are made and averaged. The Stop on Pass and measure
time requirement are tested after each measurement until one or the other results in
an exit from the test cycle.

When the instrument is selected for Manual mode of operation the averaging works similar-
ly. When the [START] button is pressed to exit Charge and start measure, n measurements
are averaged. For each consecutive press of the [START] button one more measurement is

made, the last five are averaged and result displayed. The [STOP] button exits the Measure

mode to discharge the UUT normally.

«
...
44
45
46
47
48
...
»

Summary of Contents for RESISTOMAT 2408



























































































Reviews:

No comments