Burkert 8691 REV.3 Operating Instructions Manual Download Page 22

Page: 22 / 64

Mechanical installation

Connection piece

Pilot air ports

2x fastening

screw

(max. 1.5 Nm)

Figure 11:

Installation

7.3

Installing devices with external control air duct (20xx,

Classic)

Only for devices without preinstalled process valve.

Required attachment kit: Classic Type 20xx for the corresponding variant

NOTE

Damage to the device and the actuator when welding bodies.

Observe the following during installation on process valves with welded connection:

▶

Observe the installation instructions for the operating manual of the process valve.

▶

Before installing the device, weld the process valve into the pipe system.

1. Installing switch spindle

Transparent cap

Position indicator

Actuator

Figure 12:

Installing the switch spindle (1), external pilot air duct

→

Unscrew the transparent cap from the actuator.

→

Unscrew the position indicator of the spindle with hex key.

english

Type 8691 REV.3

Summary of Contents for 8691 REV.3

































































Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands

Burkert 8691 REV.3, Operating Instructions Manual

Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands