Burkert 8691 REV.3 Operating Instructions Manual Download Page 31

Page: 31 / 64

Pneumatic installation

PNEUMATIC INSTALLATION

8.1

Safety instructions

DANGER

Risk of injury from high pressure and discharge of medium.

▶

Before working on the device or system, switch off the pressure. Vent or drain lines.

WARNING

Risk of injury from improper installation.

▶

Only trained technicians may perform installations.

▶

Perform installations with suitable tools only.

WARNING

Risk of injury due to unintentional activation and uncontrolled start-up of the system.

▶

Secure system against unintentional activation.

▶

Ensure that the system does not start up in an uncontrolled manner.

8.2

Connecting the device pneumatically

Exhaust air port, label: 3

Pilot air port, label: 1

Figure 23:

Connecting the device pneumatically

Important information for the problem-free functioning of the device:

▶

The installation must not cause back pressure to build up.

▶

Select a hose with sufficient cross section for the connection.

▶

Design the exhaust air line in such a way that no water or other liquid can get into the device

through the exhaust air port.

▶

The pressure supply must always be at least 0.5–1 bar above the pressure required to bring the

actuator into its end position.

→

Connect the control medium to the pilot air port (1)

(3–7 bar, instrument air, oil-free, anhydrous and dust-free).

→

Connect the exhaust air line or a silencer to the exhaust air port (3).

Exhaust air system:

▶

To maintain the IP67 degree of protection, install an exhaust air line in the dry area.

english

Type 8691 REV.3

Summary of Contents for 8691 REV.3

































































Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands

Burkert 8691 REV.3, Operating Instructions Manual

Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands