Burkert 8691 REV.3 Operating Instructions Manual Download Page 11

Page: 11 / 64

Product description

PRODUCT DESCRIPTION

5.1

Structure

The modular design of the device supports various configurations and variants.

Pilot LED (yellow)

ASi PWR LED (green)*

ASi FAULT LED (red)*

Status indicator (RGB LED)

Manual LED (red)

Inv.ValveDir LED (green)

büS service interface

Key 1
Key 2

View without transparent cap and body casing:

Electrical connection

Pressure limiting valve

Exhaust air port, label: 3

Pilot air port, label: 1

only for AS-Interface variant

Figure 1:

Structure

5.1.1

Structure, integrated pilot air duct (21xx, Element)

The structure with integrated pilot air duct is optimized for mounting on process valves of the 21xx series

(Element).

Transparent cap

Body casing

Air intake filter

Fastening screw

Basic housing

Figure 2:

Structure, integrated pilot air duct

5.1.2

Structure, external pilot air duct (20xx, Classic)

The structure with external pilot air duct is optimized for mounting on process valves of the 20xx series (Classic).

Transparent cap

Body casing

Air intake filter

Fastening screw

Basic housing

Pilot air outlet 2-1
Pilot air outlet 2-2

Figure 3:

Structure, external pilot air duct

So that the pilot air can be externally connected to the actuator, this structure has a different basic housing.

english

Type 8691 REV.3

Summary of Contents for 8691 REV.3

































































Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands

Burkert 8691 REV.3, Operating Instructions Manual

Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands