Burkert 8691 REV.3 Operating Instructions Manual Download Page 7

Page: 7 / 64

About these instructions

ABOUT THESE INSTRUCTIONS

The operating instructions describe the entire life cycle of the device.

→

Keep these instructions ready to hand at the operation site.

Important safety information.

▶

Carefully read these instructions.

▶

Observe in particular the safety instructions, intended use and operating conditions.

▶

Persons, who work on the device, must read and understand these instructions.

1.1

Symbols

DANGER

Warns of an immediate danger.

▶

Failure to observe the warning will result in a fatal or serious injury.

WARNING

Warns of a potentially dangerous situation.

▶

Failure to observe the warning may result a fatal or serious injury.

CAUTION

Warns of a possible danger.

▶

Failure to observe the warning may result in moderate or minor injuries.

NOTE

Warns of damage to property.

▶

Failure to observe the warning may result in damage to device or system.

Indicates important additional information, tips and recommendations.

Refers to information in these operating instructions or in other documentation.

▶

Designates an instruction for risk prevention.

→

Designates a procedure which you must carry out.

Indicates a result.

1.2

Definition of terms

In these instructions the term “device” denotes the following device types:
Control head Type 8691 REV.3
The term “büS” (Bürkert system bus) used in this instruction stands for the communication bus developed

by Bürkert and based on the CANopen protocol.

english

Type 8691 REV.3

Summary of Contents for 8691 REV.3

































































Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands

Burkert 8691 REV.3, Operating Instructions Manual

Search results

Summary of Contents for 8691 REV.3

Reviews:

Related manuals for 8691 REV.3

Brands by name

Popular brands