background image

Page 2

CONTENTS

User Notices ............................................................. 3
Electrical Requirements ............................................ 4
Plumbing Requirements ........................................... 4
Initial Set-Up ............................................................. 5
Operating Controls.................................................... 5
Cleaning .................................................................... 6
Tea Brewing .............................................................. 6
Adjustments and Optional Settings ........................... 7
Troubleshooting ........................................................ 8
Service .................................................................... 15
Wiring Schematics.................................................. 26

INTRODUCTION

This equipment will brew a four-gallon batch of fresh tea into an awaiting dispenser.  The tea will be dispensed at

approximately room temperature to conserve ice.  The brewer also has a hot water faucet for allied beverage use. The
brewer is only for indoor use on a sturdy counter or shelf.

WARRANTY

Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects

in material and workmanship existing at the time of manufacture and appearing within one year from the date of
installation. In addition:

1.) Bunn warrants electronic circuit and/or control boards to be commercially free from defects in material and

workmanship for three years from the date of installation.

2.) Bunn warrants the compressor on refrigeration equipment to be commercially free from defects in material

and workmanship for two years from the date of installation.

3.) Bunn warrants that the grinding burrs on coffee grinding equipment will grind coffee to meet original factory

screen sieve analysis for three years from date of installation or for 30,000 pounds of coffee, whichever comes first.

This warranty does not apply to any equipment, component or part that was not manufactured by Bunn or that,

in Bunn’s judgement, has been affected by misuse, neglect, alteration, improper installation or operation, improper
maintenance or repair, damage or casualty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR

ORAL,  EXPRESS  OR  IMPLIED,  INCLUDING,  BUT  NOT  LIMITED  TO,  ANY  IMPLIED  WARRANTY  OF  EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 

The agents, dealers or employees of Bunn are

not authorized to make modifications to this warranty or to make additional warranties that are binding on Bunn.
Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and should not
be relied upon.

The Buyer shall give Bunn prompt notice of any claim to be made under this warranty by telephone at (217)

529-6601 or by writing to Post Office Box 3227, Springfield, Illinois, 62708-3227. If requested by Bunn, the Buyer
shall ship the defective equipment prepaid to an authorized Bunn service location. If Bunn determines, in its sole
discretion, that the equipment does not conform to the warranty, Bunn shall repair the equipment with no charge
for parts during the warranty period and no charge for labor by a Bunn Authorized Service Representative during
the warranty period. If Bunn determines that repair is not feasible, Bunn shall, at its sole option, replace the
equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE

OF  THIS  EQUIPMENT,  WHETHER  DERIVED  FROM  WARRANTY  OR  OTHERWISE,  SHALL  BE  LIMITED,  AS
SPECIFIED HEREIN, TO REPAIR OR, AT BUNN’S SOLE OPTION, REPLACEMENT OR REFUND.

In no event shall Bunn be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,

loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.

33030 082901

Summary of Contents for TU3QF-EZ



























Reviews: