Bunn Single SH Operating & Service Manual Download | Manualshive

Page: 8 / 44

background image

Page 8

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems

encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic
Technical Service Department.

•

Inspection, testing, and repair of electrical equipment should be performed only by qualified service
personnel.

•

All electronic components have 120 - 240 volt ac and low voltage dc potential on their terminals.
Shorting of terminals or the application of external voltages may result in board failure.

•

Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be
permanent. If an intermittent condition is encountered, the cause will likely be a switch contact or
a loose connection at a terminal or crimp.

•

Solenoid removal requires interrupting the water supply to the valve. Damage may result if
solenoids are energized for more than ten minutes without a supply of water.

•

The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened.
This will help avoid twists and kinks in the tubing.

•

Make certain that all plumbing connections are sealed and electrical connections tight and isolated.

•

This brewer is heated at all times. Keep away from combustibles.

WARNING

•

Exercise extreme caution when servicing electrical equipment.

•

Disconnect power source when servicing, except when electrical tests are specified.

•

Follow recommended service procedures.

•

Replace all protective shields or safety notices.

Probable Cause

1. No power or incorrect voltage

1. No water

Problem

Equipment will not operate.

Brew cycle will not start.

Remedy

(A1)  Check  the  terminal  block  for
120 volts across the black and white
terminals on 120 volt two wire brew-
ers.
(A2)  Check  the  terminal  block  for
120 volts across the red and white
terminals  and  the  black  and  white
terminals  on  120/208  or  120/240
volt brewers.
(A3)  Check  the  terminal  block  for
200 volts on "B Series" brewers or
240  volts  on  "A  Series"  brewers
across the red and black terminals.

(B) Check circuit breakers or fuses.

Check plumbing and shut-off valves

28230 092200

«
...
6
7
8
9
10
...
»

Summary of Contents for Single SH













































Reviews:

No comments

Related manuals for Single SH

Brand: LabelTac Pages: 32

Exprelia Evo HD8855

Brand: Saeco Pages: 80

Brand: Russell Hobbs Pages: 8

Brand: Guzzanti Pages: 63

Brand: Binatone Pages: 50

Brand: Summit Pages: 28

Brand: Chefman Pages: 5

NAVIGLIO HD8749/01

Brand: Gaggia Pages: 48

Brand: Omcan Pages: 12

Brand: Brady Pages: 48

the Barist Express SES875

Brand: Sage Pages: 48

Brand: Nespresso Pages: 44

Brand: Follett Pages: 12

Brand: Hamilton Beach Pages: 11

intactidea Royal Grinder

Brand: Flair Espresso Pages: 2

Brand: Bodum Pages: 16

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands