Bunn Single SH Page 10 Operating & Service Manual Download

Page: 10 / 44

Page 10

Problem

Beverage level will not adjust (Selec-
tor switch in any position)

Water flows into tank continuously
(ON/OFF Switch "ON")

Water flows into tank continuously
(ON/OFF Switch "OFF")

Water from tank is not hot

Spitting or unusual steaming from
sprayhead or airvent.

Remedy

Refer to

Service - Selector switch for

testing procedures. See page 16

Refer to

Service - Timer for testing

procedures. See page 36 & 38

Refer to

Service - Level control board

for test procedures. See page 26

Refer to

Service - Overflow protec-

tion switch for testing procedures.
See page 25

Refer to

Service - Solenoid valve for

testing procedures. See page 32

Refer to

Service -Limit thermostat

for testing procedures. See page 19

Refer to

Service - Control thermo-

stat for testing procedures. See page
22

Refer to

Service - Contactor for test

procedures. See page 20

Refer to

Service - Tank heater for

testing procedures. See page 34

Refer to

Service - Control thermo-

stat for testing procedures. See page
22

Inspect the tank assembly for ex-
cessive lime deposits. Delime as
required.

Probable Cause

1. Brew selector switch

1. Timer

1. Level control board and level probe

2. Overflow protection switch

3. Solenoid valve

1. Limit thermostat

CAUTION

- Do not eliminate or by-

pass limit thermostat. Use only
B.O.M. Part #23717.0001

2. Control thermostat

3. Contactor

4. Tank heater

1. Control thermostat

2. Lime build-up

CAUTION

- Tank and tank compo-

nents should be delimed regularly
depending on local water conditions.
Excessive mineral build-up on stain-
less steel surfaces can initiate cor-
rosive reactions resulting in serious
leaks.

TROUBLESHOOTING (cont.)

28230 092200

Summary of Contents for Single SH













































Search results

Summary of Contents for Single SH

Reviews:

Related manuals for Single SH

Brands by name

Popular brands

Bunn Single SH, Operating & Service Manual

Search results

Summary of Contents for Single SH

Reviews:

Related manuals for Single SH

Brands by name

Popular brands