Bunn Single SH Page 24 Operating & Service Manual Download | Manualshive

Page: 24 / 44

background image

Page 24

DISPENSE VALVE

SERVICE (cont.)

P829

FIG. 14 DISPENSE VALVE

Location:

Dispense valve is located inside the hood directly

above the sprayhead.

Test Procedures:
1. Disconnect the brewer from the power source.
2. Disconnect the wires from the dispense valve and

check the voltage across the white/violet wire  and
white/green  wire.  Connect  brewer  to  the  power
source.  Place  the  "ON/OFF"  switch  in  the  "ON"
position, press and release the start switch. The
indication must be:
a.) 120 volts ac for two wire 120 volt models, three
wire 120/208 volt models and three wire 120/240
volt models.
b.) 200 to 240 volts ac for two wire 200, 230 or 240
volt models.

3. Disconnect brewer from the power source.

If voltage is present as described in step 2 proceed to
#4.
If voltage is not present as described, refer to the
wiring diagrams and check the brewer wiring harness.

FIG. 15 DISPENSE VALVE TERMINALS

22978.0000

TL5

TL4

TL3

TL2

TL1

J2

J1

SE

T

LO

CK

LOCK

SET

1

2

3

4

5

6

1 2 3 4 5 6

BUNN

90 psig max operating pressure

Strainer/Flow Control # 22300.033 0

(Repl. Flow Washer #20526.0330)

(Repl. Screen #23721.0000)

.500 gpm FLOW

P2230

WHI/VIO to Timer TL1
WHI/VIO to ON/OFF Switch
WHI/RED to Brew Selector Switch

WHI/GRN to Timer TL4
WHI/GRN to By-Pass Valve

28230 092200

4. Check for continuity across the dispense valve coil

terminals.

If continuity is present as described, reconnect the
wires to the dispense valve and proceed to #5.
If continuity is not present as described, replace the
dispense valve.

5. Check the dispense valve for coil action. Connect

the brewer to power source. Place the "ON/OFF"
switch in the "ON" position, press and release the
start switch. Listen carefully in the vicinity of the
dispense valve for a "clicking" sound as the coil
magnet attracts and repels the plunger.

6. Disconnect the brewer from the power source.

If the sound is heard as described, there may be a
blockage in the dispense valve or the water line to the
sprayhead. Remove the dispense valve and inspect for
wear, and remove waterborne particles.
If the sound is not heard as described, replace the
dispense valve.

Removal and Replacement:
1. Disconnect wires from dispense valve.
2. Drain enough water from the tank so the dispense

valve is above the water level.

3. Remove water lines and hose barb fitting from

dispense valve.

4. Remove dispense valve from the sprayhead panel.
5. Install new dispense valve .
6. Reconnect the water lines, hose barb fitting and

the wires to the dispense valve.

7. Refer to Fig. 15 when reconnecting wires.

«
...
22
23
24
25
26
...
»

Summary of Contents for Single SH













































Reviews:

No comments

Related manuals for Single SH

Brand: Necta Pages: 44

Brand: Morphy Richards Pages: 8

Brand: Hamilton Beach Pages: 12

Brand: tomado Pages: 20

Brand: Saeco Pages: 40

Brand: BIXOLON Pages: 2

U-CLR1215SOD-00A

Brand: U-Line Pages: 55

Brand: Ice Cream Depot Pages: 12

Brand: Electrolux Pages: 7

Brand: Saturn Pages: 15

Brand: TZS First AUSTRIA Pages: 26

Brand: Spidem Pages: 17

Brand: Spinel Pages: 142

Brand: Spidem Pages: 96

Brand: WMF Pages: 100

EASY-PRESSO EP-100

Brand: 3A MEDES Pages: 5

Brand: DeLonghi Pages: 13

Brand: DeLonghi Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands