Bunn Single SH Operating & Service Manual Download

Page: 11 / 44

Page 11

TROUBLESHOOTING (cont.)

Problem

Inconsistent beverage level in server.

Consistently high or low beverage
level in server.

Dripping from sprayhead.

Water overflows filter.

Beverage overflows server.

Probable Cause

1. Strainer/flow control (.500 GPM)

2. Improper water pressure

3. Dispense valve

1. Timer adjustment

1. Dispense valve

1. Bypass valve

2. Type of paper filters

3. No sprayhead

1. Beverage left in server

2. Timer adjustment

3. Dispense valve

Remedy

(A) Direction of flow arrow must be
pointing towards the brewer.

(B) Remove the strainer/flow con-
trol and check for obstructions. Clear
or replace.

Check the operating water pressure
to the brewer. It must be between 20
and 90 psi (138 and 620 kPa).

Refer to

Service - Dispense valve for

testing procedures. See page 24

Adjust the timer as required to
achieve the recommended volume
for each brew cycle.

Refer to

Service - Dispense valve for

testing procedures. See page 24

Refer to

Adjustments on page 4 step

#7. For test procedures see page 15

BUNN

paper filters should be used

for proper extraction.

Check sprayhead

The brew cycle should be started
only with an empty server under the
funnel.

Adjust the timer as required to
achieve the recommended volume
for each brew cycle.
Refer to

Service - Timer for testing

procedures. See page 36 & 38

Refer to

Service - Dispense valve for

testing procedures. See page 24

28230 092200

Summary of Contents for Single SH













































Search results

Summary of Contents for Single SH

Reviews:

Related manuals for Single SH

Brands by name

Popular brands

Bunn Single SH, Operating & Service Manual

Search results

Summary of Contents for Single SH

Reviews:

Related manuals for Single SH

Brands by name

Popular brands