Bunn Single SH Operating & Service Manual Download | Manualshive

Page: 4 / 44

background image

Page 4

Electrical Hook-Up

CAUTION –

Improper electrical installation will damage electronic components.

1. An electrician must provide electrical service as specified.
2. Using a voltmeter, check the voltage and color coding of each conductor at the electrical source.
3. Remove the front panel beneath the sprayhead and rotate the control thermostat knob fully counterclockwise

to the “OFF” position.

4. Feed the cord through the strain relief and connect it to the terminal block.
5. Connect the brewer to the power source and verify the voltage at the terminal block before proceeding. Replace

the front panel.

6. If plumbing is to be hooked up later be sure the brewer is disconnected from the power source. If plumbing

has been hooked up, the brewer is ready for Initial Set-Up.

PLUMBING REQUIREMENTS

This brewer must be connected to a cold water system with operating pressure between 20 and 90 psi (138

and 620 kPa) from a

1

⁄

2

" or larger supply line. A shut-off valve should be installed in the line before the brewer. Install

a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The water
inlet fitting is

1

⁄

4

" flare.

NOTE –

Bunn-O-Matic recommends

1

⁄

4

" copper tubing for installations of less than 25 feet and

3

⁄

8

" for more than

25 feet from the

1

⁄

2

" water supply line. A tight coil of copper tubing in the water line will facilitate moving the brewer

to clean the countertop. Bunn-O-Matic does not recommend the use of a saddle valve to install the brewer. The
size and shape of the hole made in the supply line by this type of device may restrict water flow.

This equipment must be installed to comply with the Basic Plumbing Code of the

Building Officials and Code Administrators International, Inc. (BOCA)

and the Food Service Sanitation Manual of the Food and Drug Administration (FDA).

Plumbing Hook-Up

1. Flush the water line and securely attach it to the flare fitting or quick disconnect fitting located on the bottom

of the brewer.

2. Turn on the water supply.

28230 092200

«
...
2
3
4
5
6
...
»

Summary of Contents for Single SH













































Reviews:

No comments

Related manuals for Single SH

Brand: U-Line Pages: 21

Brand: LabelStation Pages: 32

Brand: Taurus Pages: 40

Brand: UFESA Pages: 27

Brand: Atag Pages: 44

Brand: MAGIMIX Pages: 54

Brand: Netum Pages: 18

Brand: Saeco Pages: 11

Brand: Curtis Pages: 19

Brand: West Bend Pages: 68

Bakers Delight RHBM1500

Brand: Russell Hobbs Pages: 23

Brand: U-Line Pages: 20

Brand: U-Line Pages: 2

Brand: Ice-Tech Pages: 22

Brand: MicroLux Pages: 10

Brand: Saeco Pages: 33

Brand: Saeco Pages: 48

Brand: Klarstein Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands