Bunn Single SH Operating & Service Manual Download | Manualshive

Page: 7 / 44

background image

Page 7

OPERATING CONTROLS

BREW SELECTOR SWITCH

Placing the switch in the 1/2 gallon, 1 gallon, 1-1/2 or 1-3/4 gallon position selects the amount of coffee to be

brewed in subsequent brew cycles. Repositioning this switch after a brew cycle has been initiated does not change
the brew batch in progress.

ON/OFF SWITCH

Placing the switch in the unlighted lower position cuts power to the timer and stops brewing. Stopping a brew

cycle after it has been started will not stop the flow of water from the funnel. Placing the switch in the lighted upper
position supplies power to the timer and enables the brew circuit.

START SWITCH

Momentarily pressing and releasing this switch starts a brew cycle when the On/Off switch is in the lighted

upper position.

NOTE:

The On/Off switch must be in the lighted upper position to initiate and complete a brew cycle.

COFFEE BREWING

1. Select the desired batch size.
2. Insert a BUNN

®

filter into the funnel.

3. Pour the proper amount of fresh coffee into the filter and level the bed of grounds by gently shaking.
4. Slide the funnel into the funnel rails.
5. Place an empty server under the funnel.
6

Place the On/Off switch in the lighted upper position. Momentarily press and release the start switch.

7. When brewing is completed, simply discard the grounds and filter.

CLEANING

1. The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all

surfaces on Bunn-O-Matic equipment.

2. Check and clean the sprayhead. The sprayhead holes must always remain open.

NOTE –

In hard water areas, this may need to be done daily. It will help prevent liming problems in the brewer and

takes less than a minute.

28230 092200

«
...
5
6
7
8
9
...
»

Summary of Contents for Single SH













































Reviews:

No comments

Related manuals for Single SH

Brand: M&V S.r.l. Pages: 24

Brand: wacaco Pages: 7

Brand: Tescoma Pages: 4

s-class Incanto rondo

Brand: Saeco Pages: 16

Brand: U-Line Pages: 48

Brand: OK. Pages: 63

CONCETTO EVO CAPPUCCINO

Brand: Gaggia Milano Pages: 57

Brand: BRAYER Pages: 52

Brand: Breville Pages: 10

Brand: Gaggia Pages: 8

Brand: Capresso Pages: 4

Brand: Aurora Pages: 20

Brand: Rancilio Pages: 34

Brand: La Pavoni Pages: 178

Brand: Klarstein Pages: 51

Brand: Frigomat Pages: 97

FCM12SS Millenium

Brand: Farberware Pages: 12

ECAM44.62 Series

Brand: DeLonghi Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands