Bunn Single SH Page 22 Operating & Service Manual Download | Manualshive

Page: 22 / 44

background image

Page 22

Location:

The control thermostat is located inside the lower

left front of the brewer on the component bracket.

1. Disconnect the brewer from the power source.
2. Locate the blue wires on the control thermostat.
3. With a voltmeter, check the voltage across the blue

wires  on  the  control    thermostat  and  the  white
insert on the two or three pole 120V, 120/208V,
120/240V terminal block and the red insert on two
pole  200V or 240V terminal blocks. Connect the
brewer to the power source. The indication must
be:
a.) 120 volts ac for two wire 120 volt models,  three
wire 120/208 volt models and three wire 120/240
volt models.
b.) 200 to 240 volts ac for two wire 200, 230 or 240
volt models.

4. Disconnect the brewer from the power source.

FIG.12 CONTROL THERMOSTAT

22978.0000

TL5

TL4

TL3

TL2

TL1

J2

J1

SE

T

LO

CK

LOCK

SET

1

2

3

4

5

6

1 2 3 4 5 6

BUNN

90 psig max operating pressure

Strainer/Flow Control # 22300.033 0

(Repl. Flow Washer #20526.0330)

(Repl. Screen #23721.0000)

.500 gpm FLOW

P2230

SERVICE (cont.)

CONTROL THERMOSTAT

If voltage is present as described, reconnect the wire
and proceed to #5.
If voltage is not present as described, refer to the
wiring diagrams and check the brewer wiring harness.

5. Locate the black wires on the control thermostat.
6. Gently remove the capillary bulb and grommet

from the tank.

7. Check the voltage across the black wire of the

control thermostat and the white insert on the two
pole or three pole 120V, 120/208V or 120/240V
terminal  blocks  and  the  red  insert  on  two  pole
200V/240V terminal blocks with a voltmeter when
the control thermostat is turned "ON" (fully clock-
wise). Connect the brewer to the power source.
The indication must be:
a.) 120 volts ac for two wire 120 volt models, three
wire 120/208 volt models and three wire 120/240
volt models.
b.) 200 to 240 volts ac for two wire 200, 230  or 240
volt models.
Voltage must not be indicated across these termi-
nals  when  the  thermostat  is  turned  "OFF"  (fully
counterclockwise).

8. Disconnect the brewer from the power source.

If voltage is present as described,  reinstall the capil-
lary tube into the tank to the line  7" above the bulb, the
control thermostat is operating properly.
If  voltage  is  not  present  as  described,  replace  the
thermostat.

28230 092200

«
...
20
21
22
23
24
...
»

Summary of Contents for Single SH













































Reviews:

No comments

Related manuals for Single SH

Brand: Sanremo Pages: 5

Brand: OK. Pages: 63

Brand: Magic Chef Pages: 20

Brand: EOS Pages: 58

Brand: Marvel Pages: 28

Brand: Ugolini Pages: 132

Brand: Magic Chef Pages: 12

Brand: Caterlite Pages: 40

FCM12SS Millenium

Brand: Farberware Pages: 12

EasyLine ECG2003S

Brand: Electrolux Pages: 12

AEG EASYPRESSO EA110

Brand: Electrolux Pages: 32

EASYGRIND EEG100

Brand: Electrolux Pages: 44

AEG EA 1 Series

Brand: Electrolux Pages: 96

Brand: Electrolux Pages: 100

Brand: Electrolux Pages: 124

AEG KAM 2 automatic Series

Brand: Electrolux Pages: 128

Pro Line MARA X PL62X

Brand: Lelit Pages: 28

Brand: OTTOLINA Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands