background image

CCD-Premium

Operating manual

page 10 /24

If you want to use a laser exposure unit instead of a
spindle, you can remove the spindle by solving the two
fixing   screws,   then   insert   the   laser   and   park   the
spindle momentarily  on the  left   of  the  machine.   Re-
move pressure foot or depth limiter for laser exposure.
Take care that the guiding nose of the laser unit is cor-
rectly   mounted.   Mounting   of   the   dispenser   (option)
works analogously.

 At last connect the cable of the USB-camera to your computer. Use
an active hub with power supply if necessary.

In the picture on the right you can see
an   axis   and   zero-point   overview.   All
CCD machines are set up, so that the
motor connection box with the cables
is located on the left and the stepper
motor  of   the  Y-axis  facing   the  front.
On  the right   there  are  the tool  slots
(ATC-machines). If you stand in front
of the machine that way, then the 

ma-

chine zero

 is on the 

front left

, the 

X-

axis

  is   on   the  

table   level

  between

motor connection box and tool slots,
the  

Y-axis

  is   the   upper  

cross   tra-

verses

  and   the  

Z-axis

  with   the

spindle   sits   on   the   traverse   and

moves vertically

.

Bungard Elektronik GmbH & Co. KG, Rilkestraße 1, 51570 Windeck – Germany

Tel.: +49 (0) 2292/5036, Fax: +49 (0) 2292/6175, E-mail: [email protected]

Summary of Contents for CCD/2

























Reviews: