42
EN
M1.2.MRD500H.NLFREN - 08022018
3. Move the choke lever to the CLOSED position.
If the engine is hot, closing the choke is not necessary.
4. Move the throttle lever slightly to the FAST speed.
5. Pull the recoil starter until the engine starts. Return the recoil to the home position after each pull. Repeat the steps as
needed. Once engine has started, set the throttle to the FAST position before you operate the unit.
WARNING!
A rapid retraction on the starter cord (kickback) will pull your hand and arm toward the engine
faster than you can let go. Broken bones, fractures, bruises or sprains could result.
Operating
• After engine warms up, pull throttle lever to accelerate engine speed.
• Engage the required gear and slowly squeeze the clutch control lever. If the gear does not engage straight away, slowly
release the clutch lever and try again. In this way the tracked dumper will start moving.
• The tracked dumper has the steering levers on the handlebars and this makes steering very easy. To turn right or left, simply
operate the corresponding right or left steering lever.
• The sensitivity of the steering increases in proportion to the speed of the machine and the load. With an empty machine, a
light pressure on the lever is all that is needed to turn. When the machine is loaded, more pressure is required.
• The tracked dumper has a maximum capacity of 500 kg. However, it is advisable to assess the load and adjust it according
to the ground on which the machine will be used.
• It is therefore advisable to cover such stretches using low gear and taking extra care. In such situations, the machine should
be kept in low gear for the whole stretch.
• Avoid sharp turns and frequent changes of direction while driving on the road, in particularly on rough, hard terrains full of
sharp, uneven points with a high degree of friction.
• Even though the unit has rubber tracks, remember to be careful when working in adverse weather conditions (ice, heavy
rain and snow) or on types of ground that could make the tracked dumper unstable.
• Please note that as this is a tracked vehicle, it is subject to a considerable pitching movement when passing over bumps,
holes and steps.
• When the clutch control lever is released, the machine will stop and brake automatically.
• If the machine is stopped on a steep slope, a wedge should be placed against one of the tracks.
Idle speed
Set throttle control lever to its SLOW position to reduce stress on the engine when working is not being performed. Lowering the
engine speed to idle the engine will help extend the life of the engine, as well as conserve fuel and reduce the noise level of the
machine.
Stopping engine
To stop the engine in an emergency, simply turn the engine switch to the OFF position. Under normal conditions, use the
following procedure.
1. Move the throttle lever to the SLOW position.
2. Let engine idle for one or two minutes.
3. Turn the engine switch to the OFF position.
4. Turn the fuel valve lever to the OFF position.
MINI TRACKED DUMPER
13
GB
IMPORTANT: DO NOT OVERFILL!
This equipment and/or its engine
may include evaporative emissions
c o n t r o l s y s t e m c o m p o n e n t s ,
required to meet EPA and/or CARB
regulations, that will only function
properly when the fuel tank has been
filled to the recommended level.
Overfilling may cause permanent
damage to evaporative emissions
control system components. Filling
to the recommended level ensures
a vapor gap required to allow for
fuel expansion. Pay close attention
while filling the fuel tank to ensure
that the recommended fuel level
inside the tank is not exceeded. Use
a portable gasoline container with an
appropriately sized dispensing spout
when filling the tank. Do not use a
funnel or other device that obstructs
the view of the tank filling process.
Rapid retraction of the starter cord
(kickback) will pull your handand arm
toward the engine faster than you
can let go. Broken bones, fractures,
bruises, or sprains could result.
3. Reinstall the fuel cap and tighten. Always
clean up spilled fuel.
SLOW
FAST
OPEN
CLOSED
ON
OFF
ON
OFF
SLOW
FAST
OPEN
CLOSED
Starting Engine
1. Move the engine
switch to the ON
position.
2. Open the fuel shut-
off valve.
3. Move the choke
lever to the
CLOSED position.
If the engine is hot,
closing the choke is
not necessary.
4. Move the throttle
lever slightly to the
FAST speed.
5. Pull the recoil starter until the engine starts.
Return the recoil to the home position after
each pull. Repeat the steps as needed. Once
engine has started, set the throttle to the
FAST position before you operate the unit.
Operating
After the engine warms up, move the throttle
lever to accelerate engine speed.
Engage the required gear and slowly squeeze
the clutch control lever. If the gear does not
engage immediately, slowly release the clutch
lever and try again. In this way the mini tracked
dumper will start moving.
The mini tracked dumper has the steering
levers on the handlebars, which makes steering
very easy. To turn right or left, simply pull the
corresponding right or left steering lever.
The sensitivity of the steering increases in
proportion to the speed of the machine and the
load. With an empty machine, a light pressure
on the lever is all that is needed to turn. When
the machine is fully loaded, more pressure is
required.
The mini tracked dumper has a maximum
capacity of 1100 LBS. However, it is advisable
to assess the load and adjust it according to
the ground on which the machine will be used.
It is therefore advisable to cover such stretches
using low gear and taking extra care. In such
situations, the machine should be kept in low
gear for the whole stretch.
09735UK00M110.indd 13
2017/12/20 16:56:29
MINI TRACKED DUMPER
13
GB
IMPORTANT: DO NOT OVERFILL!
This equipment and/or its engine
may include evaporative emissions
c o n t r o l s y s t e m c o m p o n e n t s ,
required to meet EPA and/or CARB
regulations, that will only function
properly when the fuel tank has been
filled to the recommended level.
Overfilling may cause permanent
damage to evaporative emissions
control system components. Filling
to the recommended level ensures
a vapor gap required to allow for
fuel expansion. Pay close attention
while filling the fuel tank to ensure
that the recommended fuel level
inside the tank is not exceeded. Use
a portable gasoline container with an
appropriately sized dispensing spout
when filling the tank. Do not use a
funnel or other device that obstructs
the view of the tank filling process.
Rapid retraction of the starter cord
(kickback) will pull your handand arm
toward the engine faster than you
can let go. Broken bones, fractures,
bruises, or sprains could result.
3. Reinstall the fuel cap and tighten. Always
clean up spilled fuel.
SLOW
FAST
OPEN
CLOSED
ON
OFF
ON
OFF
SLOW
FAST
OPEN
CLOSED
Starting Engine
1. Move the engine
switch to the ON
position.
2. Open the fuel shut-
off valve.
3. Move the choke
lever to the
CLOSED position.
If the engine is hot,
closing the choke is
not necessary.
4. Move the throttle
lever slightly to the
FAST speed.
5. Pull the recoil starter until the engine starts.
Return the recoil to the home position after
each pull. Repeat the steps as needed. Once
engine has started, set the throttle to the
FAST position before you operate the unit.
Operating
After the engine warms up, move the throttle
lever to accelerate engine speed.
Engage the required gear and slowly squeeze
the clutch control lever. If the gear does not
engage immediately, slowly release the clutch
lever and try again. In this way the mini tracked
dumper will start moving.
The mini tracked dumper has the steering
levers on the handlebars, which makes steering
very easy. To turn right or left, simply pull the
corresponding right or left steering lever.
The sensitivity of the steering increases in
proportion to the speed of the machine and the
load. With an empty machine, a light pressure
on the lever is all that is needed to turn. When
the machine is fully loaded, more pressure is
required.
The mini tracked dumper has a maximum
capacity of 1100 LBS. However, it is advisable
to assess the load and adjust it according to
the ground on which the machine will be used.
It is therefore advisable to cover such stretches
using low gear and taking extra care. In such
situations, the machine should be kept in low
gear for the whole stretch.
09735UK00M110.indd 13
2017/12/20 16:56:29
copyrighted
document
- all
rights
reserved
by
FBC