build 829700123 Manual Download Page 36

36

EN

M1.2.MRD500H.NLFREN - 08022018

Safety instructions

1. 

Read and understand the operator’s manual and labels affixed to the machine. Learn its application and limitation as well 

as the specific potential hazards.

2.  Make sure thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage 

the controls quickly.

3.  Make sure to read and understand all instructions and safety precautions of the engine manual delivered with the 

machine. Do not use the machine until you have completely understood the specific operating methods. Always follow the 

manufacturer’s instruction for maintenance operations.

4.  The exhaust fumes are harmful to health. If use indoors, good ventilation must be provided.

5. 

Do not operate the dumper in explosive or flammable atmospheres.

6.  Walk with the machine, do not run.

7. 

Stay alert. Do not operate the machine when under the influence of drugs, alcohols or any medication that could affect 

your ability to use it properly.

8.  Dress properly. Wear boots and gloves. Do not wear loose clothing.

9.  Use safety equipment. Always wear eye protection and hearing protection.

10.  Check your machine before starting. Keep guards in place and in working order. Make sure all nuts and bolts are securely 

tightened.

11. Never operate the machine when there is fuel leakage and the control damaged. Replace damaged, missing or failed 

parts before using the machine.

12. Form a habit of checking to ensure that keys and adjusting wrenches are removed from machine area before starting it.

13. Do not overreach. Do not operate the machine with barefoot or when wearing sandals. Wear protective footwear to protect 

your feet and avoid slipping.

14. 

When fill or drain fuel, stop the machine, wait the hot parts cooled and make sure there is no ignition source, such as 

sparks, flame near the machine. Always keep the fuel far away from the ignition sources.

15. If any fuel spillage occurs during refuelling, use a dry rag to wipe up and carry the machine to another position at least 5 

m far from the spillage area to starting it.

16. Check the oil level before starting. Do not start machine when the oil level low.

17. Never change the control setting and speed limit device. Over-speed than the limitation may cause danger to the operator.

18. Never get out of your hands from the handles. Hazards rise when the machine is get out of guide.

19. The machine is only designed for adult use. Always keep the machine out of the reach of the children.

20. 

Repair, maintenance and adjustment must be performed by qualified person.

21. If the machine is no longer usable, dispose it properly without damaging the environment by handing it into your local 

dealer who will arrange for its correct disposal.

22. 

Never over-fill the fuel. Do not fill fuel exceed the limit level mark on the fuel filter of the tank.

2  Specifications and description

Model

MRD500H

Motor

6,5 hp / 196 cc

Transmission

3F + 1R

Load capacity

500 kg

Box length

950 mm

Box width

680 mm

Box depth

465 mm

Track width

180 mm

Oil tank capacity

0.6 l

Fuel tank capacity

3 l

Autonomy

4 h

Noise level

101 dB(A)

Net weight

299 kg

copyrighted 

document 

- all 

rights 

reserved 

by 

FBC

Summary of Contents for 829700123

























































Reviews: