E-8
2006 Buell Lightning: Appendix E
HOME
REMOVAL
NOTE
If solenoid bracket needs to be replaced, remove the base-
plate assembly, turn it over and remove the three fasteners
securing the bracket to the baseplate.
1.
See
Figure E-5.
Disconnect electrical connector [178]
(1).
2.
Hold solenoid shaft by flat spot provided and break cable
connector (6) loose.
3.
Unthread cable connector and disconnect cable from
solenoid (8).
4.
Loosen jam nut (5) and disconnect active cable (2) from
cable bracket (4).
NOTE
Follow next step only is solenoid is to be replaced.
5.
Loosen pinch fastener on solenoid bracket (9).
6.
Remove the two fasteners at the front on the solenoid
bracket (9) and slide solenoid (8) out of bracket.
NOTE
When removing baseplate it will be necessary to feed the
electrical connector and active cable and grommets through
the baseplate.
7.
Remove baseplate (10). See
4.44 AIR CLEANER
ASSEMBLY
.
8.
See
Figure E-3.
If the active cable needs to be replaced
disconnect from cable wheel (2).
INSTALLATION
NOTE
It solenoid bracket was removed, reinstall using the three fas-
teners and tighten to 48-60
in-lbs
(5.4-6.7 Nm).
1.
See
Figure E-5.
When installing baseplate assembly
(10) see
4.44 AIR CLEANER ASSEMBLY
.
NOTE
When installing the backing plate it is important to ensure
that the active cable remains in the tower on the cable wheel
on the throttle body. If the cable comes out the cable will not
work properly and will not be able to be adjusted.
NOTES
●
When installing baseplate be sure to feed the electrical
connector (1) through hole in baseplate first and then
insert active cable and then grommet.
●
Follow next step only if solenoid was removed.
2.
Install solenoid (8) into bracket (9) and tighten pinch fas-
tener to 48-60
in-lbs
(5.4-6.7 Nm)
and bracket to sole-
noid fasteners to
20-24
in lbs
(2.3-2.7 Nm).
3.
Install active cable (2) into bracket (4) and leave jam nut
(5) loose until the setting can be verified.
4.
Connect active cable (2) to solenoid shaft and tighten
cable connector (6) to 20-24
in lbs
(2.3-2.7 Nm).
5.
Connect electrical connector [178].
6.
See
CABLE ADJUSTMENT
and
verify active cable set-
ting.
7.
Tighten jam nuts to 48-60
in-lbs
(5.4-6.7 Nm).
Figure E-5. Disconnecting Active Intake System
1.
Electrical connector [178]
2.
Active intake cable
3.
Cable adjusting nut
4.
Cable bracket
5.
Active cable jam nut
6.
Cable connector
7.
Fasteners (2), bracket to solenoid
8.
Active intake solenoid
9.
Solenoid bracket
10. Air cleaner baseplate assembly
9
8
1
10
10904f
3
2
5
6
4
7
Summary of Contents for 2006LIGHTNING MODELS
