Brusa NLG5, User Manual

Page: 29 / 47

Betriebsanleitung NLG5 User’s manual NLG5
12.2003-NLG5xx_179_ab Nr25 29 / 47
6 Signalstecker
Control connector
6.1 Übersicht
Overview
Signal-Stecker (23-polig)
Nr. Abk. Funktion
1
GND Masse (Bordnetz Minus, Klemme 31)
2 n n n n
AUX Eingang/A14 V
(Bordnetz Plus, Klemme 30)
3 PON Power ON
4 n n n n
FLT Ausgang 1 “Nicht Bereit”
5
n
n n
n DO2 Ausgang 2 (programmierbar)
6
n
n n
n DO3 Ausgang 3 (programmierbar)
7
n n n n DO4 Ausgang 4 (programmierbar)
8 PG1 Analog Masse (für Nr. 20 - 23)
9
CNL CAN Low
10 CNH CAN High
11 TXD RS232 Transmit (9-pol D-Sub: Pin 2)
12 RXD RS232 Receive (9-pol D-Sub: Pin 3)
13 PRO Firmware-Programmierung
14 PG2 Reserve Masse
15 PG3 RS232 Masse (9-pol D-Sub: Pin 5)
16
DI1 Digital Eingang 1 (AHZ Entladepulse)
17 DI2 Digital Eingang 2 (AHZ Ladepulse)
18
DI3 Digital Eingang 3 (ext. Kriterium 1)
19 DI4 Digital Eingang 4 (ext. Kriterium 2)
20
TS1 Eingang Batterie-Temperatursensor 1
21 TS2 Eingang Batterie-Temperatursensor 2
22
TS3 Eingang Batterie-Temperatursensor 3
23 PI Eingang zur Netzstrom-Begrenzung
Control connector (23 pole)
No Abbr Function
1
GND Ground (power circuit negative, clamp
31)
2
n n n n AUX In/Out +14 V (power circuit positive,
clamp 30)
3 PON Power ON
4
n n n n FLT Output 1 “Not Ready”
5
n n n n DO2 Output 2 (programmable)
6
n
n n
n
DO3 Output 3 (programmable)
7
n n n n DO4 Output 4 (programmable)
8 PG1 Analog Ground (of No 20 - 23)
9 CNL CAN Low
10
CNH CAN High
11 TXD RS232 Transmit (9-pin D-Sub: Pin 2)
12 RXD RS232 Receive (9-pin D-Sub: Pin 3)
13 PRO Firmware programming
14
PG2 Reserve Ground
15 PG3 RS232 Ground (9 pin D-Sub: Pin 5)
16 DI1 Digital Input 1 (AHZ discharge pulses)
17 DI2 Digital Input 2 (AHZ charge pulses)
18
DI3 Digital Input 3 (ext. condition 1)
19 DI4 Digital Input 4 (ext. condition 2)
20 TS1 Input battery temp sensor 1
21
TS2 Input battery temp sensor 2
22 TS3 Input battery temp sensor 3
23 PI Mains limiter input
1 2 4 3 7 6 5 8 9 10 12 11 15 14 13 16 17 19 18 22 21 20 23
12V
- +
Rot Gelb Gelb Grün
Red Yellow Yellow Green
CAN-L CAN-H Tx Rx Gnd
RS232 RS232
ext. Ah-Zähler/ Ah-Counter BCM98-mess 3 x NTC
3A