![BRP E250DHLSCS Service Manual Download Page 138](http://html1.mh-extra.com/html/brp/e250dhlscs/e250dhlscs_service-manual_2820607138.webp)
136
ELECTRICAL AND IGNITION
ELECTRIC START CIRCUIT
Start Circuit Operation
The starter must engage and turn the flywheel.
The outboard must crank a minimum of 100 RPM
to start. Normal cranking speed is approximately
175 RPM.
Starter performance depends on the following:
•
Proper battery and cable capacity.
•
Clean, tight cable connections.
•
Solenoid activation through the key switch, neu-
tral safety switch, and
EMM
.
on p. 27 for battery,
terminal, and cable requirements.
Solenoid Wiring
The positive (B+) battery cable connects to a large
terminal of the starter solenoid. This terminal also
provides the 12 V power supply to the engine har-
ness (red wire) and the 10 A fuse. The red/purple
wire from the fuse holder (10 A) provides 12 V to
terminal “B” of key switch.
The negative (B–) battery cable connects to the
main ground stud next to starter solenoid.
Engine Wire Harness
Contains the following circuits:
•
Red/purple output wire from fuse provides 12 V
to instrument harness.
•
Purple wire provides switched 12 V to solenoid
(terminal “A”) and
EMM.
•
Yellow/red wire provides switched 12 V to
EMM.
•
Brown/white wire from terminal 11 of
EMM
J1-B
connector provides switched ground (NEG) to
starter solenoid (terminal “B”).
Instrument Wire Harness
Contains the following circuits:
•
Red/purple wire provides 12 V to key switch ter-
minal “B”.
•
Purple wire provides switched 12 V to engine
wire harness.
•
Yellow/red wire from terminal “S” of key switch
provides switched 12 V to
EMM
(key switch in
START position).
Key Switch, ON position
12 V is applied to the accessory circuit. Key
switch ON:
•
Switches 12 V to terminal “A” of key switch and
to the purple wires of the wire harnesses.
•
Provides 12 V input to terminal 21 of
EMM
J1-B
connector.
EMM
turns ON.
•
EMM
provides 12 V to terminal “A” of starter
solenoid.
1.
Key switch, ON position – Continuity between ter-
minals “B” and “A”
2.
Terminal “B”, 12 V (Red/purple)
3.
Terminal “A”, 12 V (Purple)
000691
B
M
M
C
A
S
M
B
S
A
C
M
M
B
S
A
C
M
M
B
S
A
C
M
4
5
6
1
2
3
1
2
3
Summary of Contents for E250DHLSCS
