BRP Can-Am Spyder RT 2013 Series Manual Download Page 5

Page: 5 / 47

rbl2013-002-002_a

TYPICAL - LH SIDE

1. Sub-crate that contains front cargo module

3. Remove windshield and front wheels from

crate base.

rbl2013-003-001_a

TYPICAL

1. Windshield
2. Front wheels

4. On RH side, remove six bolts and two fenders

from sub-crate.

rbs2011-014-002_a

TYPICAL - RH SIDE - SUB-CRATE THAT CONTAINS FRONT
FENDER

1. Bolts

5. On RH side, remove all

nails

holding front

fender sub-crate and remove sub-crate.

Parts Check

Ensure that the crate includes the following items
(inside front storage compartment or secured to
front of vehicle):

NOTE:

Empty all contents from front storage com-

partment.

DESCRIPTION

MODEL

QTY

Operator's

guide

Predelivery

check list

Safety DVD

Predelivery kit

Service covers

Windshield trim

Wheel caps

All

Front cargo

liner

RT-S

RT Limited

The predelivery kit includes the following items:

DESCRIPTION (LOCATION)

QTY

Wheel lug nut - black (front wheels) (RT-S)

Wheel lug nut - chrome (front wheels) (RT
and RT LTD)

Plastic bushing (rear suspension)

M10 x 140 hexagonal flange screw (rear
suspension)

M10 elastic flange nut (rear suspension)

M6 x 20 hexagonal flange screw (rear
suspension)

SERVICE

2013-2

5 / 47

Summary of Contents for Can-Am Spyder RT 2013 Series
















































Search results

Summary of Contents for Can-Am Spyder RT 2013 Series

Reviews:

Related manuals for Can-Am Spyder RT 2013 Series

Brands by name

Popular brands

BRP Can-Am Spyder RT 2013 Series, Manual

Search results

Summary of Contents for Can-Am Spyder RT 2013 Series

Reviews:

Related manuals for Can-Am Spyder RT 2013 Series

Brands by name

Popular brands