BRP Can-Am Spyder RT 2013 Series Manual Download Page 41

Page: 41 / 47

MODEL

SPYDER RT

FRONT SUSPENSION

Suspension type

Double A-arm with anti-roll bar

Suspension travel

174 mm (6.85 in)

Qty

Shock absorber

Type

SACHS twin-tube coil-over

REAR SUSPENSION

Suspension type

Air Controlled Suspension (ACS).

Compressor-controlled (ACS with remote adjustment only).

Swing arm with monoshock

Suspension travel

152 mm (5.98 in)

Qty

Shock absorber

Type

SACHS twin-tube coil-over

Preload adjustment
(ACS with manual adjustment)

Adjustable air pressure:135 kPa to 625 kPa (20 PSI to 90 PSI)

Preload adjustment
(ACS with remote adjustment)

5 positions

BRAKES

Type

Brembo

Front brake

Dual rigid discs 270 mm (10.6 in), radially mounted monobloc,

with 4 piston calipers, 2-pad

Rear brake

Single disc 270 mm (10.6 in) with 1 piston floating caliper with

integrated parking brake

Capacity

530 ml (17.9 U.S. oz)

Brake fluid

Type

DOT 4

Parking brake

Mechanical, electrically actuated to the rear caliper

Minimum brake pad thickness

1 mm (.04 in)

Minimum brake disc thickness

6.4 mm (.25 in)

Maximum brake disc warpage

0.1 mm (.004 in)

TIRES

Front

KR31 165/55R15

Type (use only tires
recommended by BRP)

Rear

KR21 225/50R15

Front

Nominal.: 103 kPa (15 PSI)

Min.: 89 kPa (13 PSI)

Max.: 117 kPa (17 PSI)

Nominal.: 193 kPa (28 PSI)

Min.: 179 kPa (26 PSI)
Max.: 207 kPa (30 PSI)

Pressure

Rear

NOTE:

The pressure difference between the left and right side tire should not

exceed 3.4 kPa (.5 PSI).

Front

2.5 mm (3/32 in)

Minimum tire tread depth

Rear

4 mm (5/32 in)

WHEELS

Front

381 mm (15 in)

x 127 mm (5 in)

Size
(diameter X width)

Rear

381 mm (15 in)

x 178 mm (7 in)

Front wheel nuts torque

90 N•m to 120 N•m (66 lbf•ft to 89 lbf•ft)

Rear drive axle nut torque

123 N•m to 137 N•m (91 lbf•ft to 101 lbf•ft)

SERVICE

2013-2

41 / 47

Summary of Contents for Can-Am Spyder RT 2013 Series
















































Search results

Summary of Contents for Can-Am Spyder RT 2013 Series

Reviews:

Related manuals for Can-Am Spyder RT 2013 Series

Brands by name

Popular brands

BRP Can-Am Spyder RT 2013 Series, Manual

Search results

Summary of Contents for Can-Am Spyder RT 2013 Series

Reviews:

Related manuals for Can-Am Spyder RT 2013 Series

Brands by name

Popular brands