BRP Can-Am Spyder RT 2013 Series Manual Download Page 42

Page: 42 / 47

MODEL

SPYDER RT

DIMENSIONS

Overall length

2 667 mm (105 in)

Overall width

1 572 mm (61.9 in)

Windshield up

1 510 mm (59.45 in)

Overall height

Windshield down

1 473 mm (58 in)

Seat (top) height

772 mm (30.4 in)

Wheelbase

1 711 mm (67.4 in)

Front wheel track

1 384 mm (54.5 in)

Ground clearance, front and under engine

110 mm (4.3 in)

WEIGHT AND LOADING CAPACITY

Dry weight

433 mm (17 in)

Capacity

55 L (14.5 U.S. gal.)

Front storage compartment

Maximum load

16 kg (35 lb)

Capacity

1.2 L (.317 U.S. gal.)

Glove box

Maximum load

2 kg (4 lb)

Capacity

49.7 L (13.13 U.S. gal.)

Rear lateral storage
compartment

Maximum load

7 kg (15 lb)

Capacity

40.5 L (10.7 U.S. gal.)

Rear center storage
compartment

Maximum load

9 kg (20 lb)

Total vehicle load allowed (including operator, passenger, cargo
and added accessories)

224 kg (493.8 lb)

Gross vehicle weight rating (GVWR)

680 kg (1,499.1 lb)

Maximum weight on trailer tongue

18.2 kg (40 lb)

Maximum towed weight (trailer and cargo)

182 kg (401 lb)

42 / 47

2013-2

SERVICE

Summary of Contents for Can-Am Spyder RT 2013 Series
















































Search results

Summary of Contents for Can-Am Spyder RT 2013 Series

Reviews:

Related manuals for Can-Am Spyder RT 2013 Series

Brands by name

Popular brands

BRP Can-Am Spyder RT 2013 Series, Manual

Search results

Summary of Contents for Can-Am Spyder RT 2013 Series

Reviews:

Related manuals for Can-Am Spyder RT 2013 Series

Brands by name

Popular brands