Brother P-Touch 580C User Manual Download Page 129

Page: 129 / 188

125

PROBLEM

REMEDY

1. The display stays blank after you have
turned on the machine or abnormal cha-
racters are displayed.

•

Check that the AC adaptor is attached

properly.

•

If you are using alkaline batteries, check

that they are properly inserted.

•

If the batteries are low, replace them.

•

Hold down

CODE

and

keys and press

the

ON/OFF

key twice to reset the mac-

hine. The display and all contents of the
memory are also deleted.

2. The machine does not print or the printed
characters are blurred.

•

Check that the tape cassette has been

inserted properly.

•

If the tape cassette is empty, replace it

with a new one.

•

Make sure that the tape cassette cover

has been closed.

3. The printed characters are not formed
properly.

•

If you are using alkaline batteries, they

may be low. Try using the AC adaptor.

4. Striped tape appears.

•

You have reached the end of the tape.

Replace it with a new tape.

5. In multi-color print mode, the tape cannot
be fed after the machine’s power supply
was suddenly cut (e.g. the power button
was pressed or there was a power failure)
while rewinding the tape, which caused
the rewinding gear to remain engaged.

•

Open the tape compartment cover, re-

move the multi-color tape cassette, then
close the cover.
Turn on the power and press the

FEED

key to disengage the rewinding gear,
causing the message “NO TAPE!” to be
displayed.

Summary of Contents for P-Touch 580C





























































































































































































Search results

Summary of Contents for P-Touch 580C

Reviews:

Related manuals for P-Touch 580C

Brands by name

Popular brands

Brother P-Touch 580C, User Manual

Search results

Summary of Contents for P-Touch 580C

Reviews:

Related manuals for P-Touch 580C

Brands by name

Popular brands