Brother P-Touch 580C User Manual Download Page 124

Page: 124 / 188

120

ERROR MESSAGE

CAUSE

REMEDY

CANCELED DATA!
PRESS ANY KEY

•

This message appears if the

CANCEL

key is pressed while

data is being transmitted from
the computer to this unit in Inter-
face mode.

•

Press any key other then the

CODE, SHIFT, ALT

CAPS

keys, then try again.

CAN’T DELETE
TAPE EDGE!

•

This message appears if the

end of the tape cannot be
detected during multi-color
printing.

•

Pull out some excess tape

and hold the end of the tape
while turning the tape roll to
tighten the tape in the cass-
ette.

•

Align the end of the tape with

the edge of the cassette,
then try using the multi-color
printing function again.

Press the

CODE

and

keys

to skip colors and return to
the point where printing
stopped.

CAN’T HERE

•

This message appears if a

character, symbol, return or
new block is entered while
the cursor is located in a bar
code field.

•

This message appears if the

cursor is located in a bar code
field and a text format (font, size
width, style, underlining and
framing, or color) key is pressed.

•

This message appears if a

text file is recalled and joined
to the current massage while
the cursor is located in a bar
code field.

•

Move the cursor or delete

the bar code field before
entering the character, sym-
bol, return or new block.

•

Move the cursor or delete

the bar code field before
pressing the text format key.

•

Move the cursor or delete

the field before recalling the
text files.

CHANGE ADAPTOR

•

This message appears if a

high-voltage adaptor is being
used.

•

Remove the high-voltage

adaptor and install the
optional 7.0V 1.2A AC
adaptor.

CLOSE
THE COVER!

•

This message appears in

any mode when the tape
compartment cover is open.

•

Close the compartment

cover.

Summary of Contents for P-Touch 580C





























































































































































































Search results

Summary of Contents for P-Touch 580C

Reviews:

Related manuals for P-Touch 580C

Brands by name

Popular brands

Brother P-Touch 580C, User Manual

Search results

Summary of Contents for P-Touch 580C

Reviews:

Related manuals for P-Touch 580C

Brands by name

Popular brands