manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 136

4-38

Confidential

Problem

Action to be taken

(7) Ink splash

Printer
• Perform the purge operation (Function code 76) several times to 

remove dust or air bubbles from its nozzles. (Refer to 

Chapter 9, 

Section 9.4.25

.)

• Check the ink cartridges. Any of them has run out of ink or the ink 

viscosity has been increased, so replace it.

• Check the head property data (Refer to 

Chapter 9, Section 9.4.21

.)

• Check that the main drain tube is not bent.

• Replace the head/carriage unit.

• Replace the main PCB.

• Replace the power supply PCB.

• Replace the maintenance unit.

(8) Print edges not aligned

Printer
• Check the alignment of vertical print lines with Function code 65 in the 

maintenance mode. (Refer to 

Chapter 9, Section 9.4.19

.)

• Perform the print head skew compensation with the head skew adjuster 

knob. Refer to 

Chapter 7, Section 7.2, [ 4 ]

.

• Check the head/carriage unit.

• Check the CR encoder strip for stains or scratches. (If the CR encoder 

strip is not hooked properly, correct it.)

• Correct the positioning error of the head/carriage unit. (Refer to 

Chapter 7, Section 7.2, [ 4 ]

.)

• Check the height adjustment mechanism of the head/carriage unit 

(Refer to 

Chapter 3, Section 3.2.2.3

.)

• If the "head-platen gap offset" is enabled with assurance mode switch 

AMS 02 (Function code 88), align the vertical print lines (Function 
code 65). (Refer to 

Chapter 9, Sections 9.4.30 and 9.4.19

.)

(9) Random missing dots

Printer
• Perform the purge operation (Function code 76) several times to 

remove dust or air bubbles from its nozzles. (Refer to 

Chapter 9, 

Section 9.4.25

.)

• Check the ink cartridges. If any cartridges have run out of ink, replace 

them.

• Check that the carriage-head flat cable is connected to the carriage 

PCB.

• Replace the head/carriage unit.

• Check the connection of the head flat cables on the main PCB. (If 

either of those cables is broken or damaged, replace it.)

• Replace the main PCB.

• Clean the head caps and wiper of the maintenance unit with a Rubycel 

stick. For the cleaning procedure, refer to 

Chapter 8, Section 8.2 

"CLEANING THE MAINTENANCE UNIT."

• Replace the maintenance unit.

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands