manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 320

9-28

Confidential

9.4.16 Updating of Paper Feeding Correction Value 

(Function code 58)

„

Function

To keep the paper feeding performance in the best condition for quality print, the controller
optimizes the rotation of the paper feed roller, using the correction value stored in the EEPROM
on the main PCB.

If you replace the engine unit or head/carriage unit, you need to update the paper feeding
correction value according to the procedure given here.

„

Operating Procedure

(1) Switch on your PC.

(2) Place the machine in the maintenance mode (see 

Section 9.1

) and set A4-size paper in the

paper tray to print check patterns.

(3) Connect the machine to your PC using a USB cable.

(4) On your PC, run "filedg32.exe" in the folder created in 

Section 7.1.1

.

The Filedrgs window appears as shown below.

For the paper feed roller adjustment

(5) Drag and drop the "pfadj.prn" onto the Brother Maintenance USB Printer driver icon in the

Filedrgs window shown above.

The machine displays the "RECEIVING DATA" on the LCD and prints out "PF adjust
check" pattern (see 

page 9-30

 for a sample printout).

(6) On the machine, press the 

5

 and 

8

 keys in this order.

The "1.PF 2.EXIT" appears on the LCD.

(7) To select the paper feed roller adjustment, press the 

1 

key.

The "PF ADJ NO. +0" appears on the LCD.

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands