Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 142

Page: 142 / 448

4-44

Confidential

[ 3 ] Auto document feeder (ADF) malfunction

An ADF failure may occur not only due to machine malfunction but also to the user's actions.

Problems due to the user's actions

Problems due to machine malfunction

Check

Possible causes

Problems that may result

Document guides

The document guides are not positioned
to match the width of document(s)
loaded.

Documents will skew.

Inside the ADF

- Foreign materials have found their

way into ADF.

- The size of the document loaded is

smaller than the specified size.

Foreign materials can hinder
document feeding.
The document will jam inside the
ADF.

Check

Possible causes

Problems that may result

ADF

The spring plates of the ADF parts are
deformed.

A document will stop halfway
through feeding.

The ADF parts are deformed or worn.

Two or more sheets of documents
will be fed through at once.

Document front sensor

- The document front sensor is

defective.

- The document front sensor actuator is

deformed.

No document will be drawn in or
recognized by the machine.
Even placing a document in the
ADF cannot switch to "ADF
scanning."

Document rear sensor

- The document rear sensor is defective.
- The document rear sensor actuator is

deformed.

A document will stop halfway
through feeding or will not be
recognized by the machine.

ADF motor

The ADF motor does not rotate.

No document will be drawn in.

Main PCB

The motor driver IC is defective.

No document will be drawn in.

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Search results

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

Reviews:

Brands by name

Popular brands

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Search results

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

Reviews:

Brands by name

Popular brands