manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 405

App. 4-31

Confidential

WSW26 

(Function setting 4)

• Selector 3: Dialing during document reading into the temporary memory in in-memory message 

transmission

If this selector is set to "0," the machine waits for document reading into the memory to
complete and then starts dialing. This enables the machine to list the total number of pages
in the header of the facsimile message.

• Selectors 4 and 5: No. of CNG cycles to be detected (when the line is connected via the external 

telephone except in the external TAD mode or via the built-in telephone)

The machine interprets a CNG as an effective signal if it detects the CNG by the number of
cycles specified by these selectors when the line is connected via the external telephone
except in the external TAD mode or via the built-in telephone.

• Selectors 6 and 7: No. of CNG cycles to be detected (when the line is connected via the external 

telephone in the external TAD mode, via the built-in telephone in the TAD 
mode, or via the machine in the automatic reception of the F/T mode)

The machine interprets a CNG as an effective signal if it detects the CNG by the number of
cycles specified by these selectors when the line is connected via the external telephone in
the external TAD mode, via the built-in telephone in the TAD mode, or via the machine in
the automatic reception of the F/T mode.

Selector 

No.

Function

Setting and Specifications

1

2

Not used.

3

Dialing during document reading 
into the temporary memory in in-
memory message transmission

0: Disable

1: Enable

4

5

No. of CNG cycles to be detected
(when the line is connected via the 
external telephone except in the 
external TAD mode or via the 
built-in telephone)

No. 4 5

0 0 :

0.5

(A)

0 1 :

1

(B)

1 0 :

1.5

(C)

1 1 :

2

(D)

6

7

No. of CNG cycles to be detected
(when the line is connected via the 
external telephone in the external 
TAD mode, via the built-in 
telephone in the TAD mode, or via 
the machine in the automatic 
reception of the F/T mode)

No. 6 7

0 0 :

0.5

(A)

0 1 :

1

(B)

1 0 :

1.5

(C)

1 1 :

2

(D)

8

Not used.

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands