manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 89

3-38

Confidential

Power transmission routes of the ASF motor and paper feed motor

The rotational torque of the ASF motor is transmitted to the ASF/maintenance drive gear which
always meshes with the clutch gear L, as described in 

Section 3.2.2.2, [ 4 ]

.

When the mode switching lever is in the left position (normal SF or high-speed feed mode), the
clutch gear L also meshes with the ASF changeover gear which transmits the ASF motor
rotation via a gear train to the paper pull-in rollers.

The rotational torque of the paper feed motor is transmitted via the PF roller gear L to the paper
feed roller that advances paper to the printing start position.

Right position (Purge mode)

Left position (ASF mode)

Mode switching lever

ASF motor

Idle gear 16

Clutch gear L

ASF changeover 
gear

ASF idle gears 17

Paper pull-in gear shaft

Purge gear

Mode switching lever

Head/carriage unit

(Front)

ASF idle
gears 17

Paper feed motor

PF roller gear L

PF motor gear

Ejection idle gear

PF timing belt

Paper ejection roller

(3_25_BHL9_A3)

Clutch gear R

ASF/maintenance 
drive gear

Paper pull-in 
rollers

Paper pull-in 
gear shaft

Paper feed roller

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands