manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 217

6-62

Confidential

Maintenance unit

(2) Release the right end of the switching lever guide from the maintenance unit and remove it.

(3) If the ink absorber box has not been removed, pull out the main drain tube from the ink

absorber box.

Note: 

Pinch the end of the main drain tube with a clip in order to prevent drained ink from

leaking and the machine from getting stained with leaked ink.

(4) Remove the three screws in the order of 

c

 to 

e

 (as shown below) from the maintenance

unit and detach the maintenance unit from the engine unit.

Assembling Notes:

• When setting the switching lever guide back into place, apply the specified lubricant to

the specified point, referring to 

Section 6.2

.

• When mounting the switching lever guide on the maintenance unit, put it on the CR

guide rail and then lightly press it.

• When mounting the maintenance unit on the engine unit, fit the two bosses of the shaft

holder (on the left side of the maintenance unit) into the two holes under the CR guide
rail.

• When securing the maintenance unit with three screws, tighten these screws in the order

of 

e

J

d

J

c

 as shown above.

• When routing the cap lift cam switch harness, pass it through the cable guide on the

maintenance unit. (See the illustration above and on 

page 6-58

.)

CR guide rail

Switching lever guide

Taptite, cup B
M3x10

Maintenance unit

ASF motor/encoder
harness

Carriage motor harness

(Front)

CR support chassis

(6_43)

1

2

3

Remove these screws in the order of      to     .  
Tighten them in the reverse order.

1

3

Apply grease here.

Cap lift cam
switch harness

Cable guide

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands