manualshive.com logo in svg

Brother MFC 5890CN - Color Inkjet - All-in-One, Service Manual

Share
Download
Brother MFC 5890CN - Color Inkjet - All-in-One Service Manual Download Page 302

9-10

Confidential

9.4.5 Firmware Switch Setting and Printout  

(Function codes 10 and 11)

(User-accessible)

[ A ] Firmware switch setting

„

Function

The machine incorporates the following firmware switch functions which can be activated with
the procedures using the control panel keys.

The firmware switches have been set at the factory in conformity to the communications
standards and codes of each country. Do not disturb them unless necessary. Some firmware
switches may not be applicable in some versions. The firmware switch data list indicates "Not
used." for those inapplicable switches.

Firmware Switches (WSW01 through WSW60)

WSW No.

Function

WSW01

Dial pulse setting

WSW02

Tone signal setting

WSW03

PBX mode setting

WSW04

TRANSFER facility setting

WSW05

1st dial tone and busy tone detection

WSW06

Pause

 key setting and 2nd dial tone detection

WSW07

Dial tone setting 1

WSW08

Dial tone setting 2

WSW09

Protocol definition 1

WSW10

Protocol definition 2

WSW11

Busy tone setting

WSW12

Signal detection condition setting

WSW13

Modem setting

WSW14

AUTO ANS facility setting

WSW15

REDIAL facility setting

WSW16

Function setting 1

WSW17

Function setting 2

WSW18

Function setting 3

WSW19

Transmission speed setting

WSW20

Overseas communications mode setting

WSW21

TAD setting 1

WSW22

ECM and call waiting caller ID

WSW23

Communications setting

WSW24

TAD setting 2

WSW25

TAD setting 3

WSW26

Function setting 4

WSW27

Function setting 5

WSW28

Function setting 6

WSW29

Function setting 7

(Not used.)

WSW30

Function setting 8

(Not used.)

WSW31

Function setting 9

WSW32

Function setting 10

WSW33

Function setting 11

Summary of Contents for MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands